The Construction Focus Four hazards

In short

The Construction Focus Four are the four hazards OSHA builds its construction outreach training around: falls, struck-by, caught-in or -between, and electrocution. Each has its own set of OSHA rules, and together they account for much of the deadliest work on a jobsite.

What are the Focus Four?

The Construction Focus Four are four hazard groups that OSHA uses as the backbone of its construction outreach training (the 10-hour and 30-hour courses):

  1. Falls: from roofs, edges, ladders, scaffolds and through holes.
  2. Struck-by: hit by a vehicle, a swinging or falling load, a flying object or falling material.
  3. Caught-in or -between: crushed or buried, as in a trench collapse, between equipment and a wall, or in moving machine parts.
  4. Electrocution: contact with power lines, energized parts or faulty tools and cords.

The point of grouping them is focus. These four drive a large share of serious construction injuries and deaths, so a safety program that controls them well has dealt with most of the worst outcomes on a typical jobsite. Some people still use the older name, the "Fatal Four."

How is each hazard controlled?

Falls

Falls are the largest single cause of construction deaths. The BLS fatality census counted 370 deaths from falls, slips and trips among construction and extraction workers in 2024, out of 1,032 deaths in that group. The main rule is the 6-foot trigger in 29 CFR 1926 Subpart M, covered in detail in construction fall protection.

Struck-by

Struck-by hazards come from motion: trucks and equipment backing up, loads swinging from cranes, materials dropped from above, and traffic in work zones. Key controls include:

  • Vehicles with an obstructed rear view may not back up unless they have a reverse alarm audible above the surrounding noise or an observer signals that it is safe (29 CFR 1926.601(b)(4)).
  • Barricaded swing radius zones around cranes and excavators.
  • High-visibility clothing and traffic control plans in roadway work.
  • Toeboards, debris nets and tool tethers to stop falling objects.

Vehicle incidents link this hazard to the fleet side of the business, covered in fleet safety and driver qualification files.

Caught-in or -between

The classic caught-in event is a trench cave-in. Soil is heavy, and a collapse gives no warning. OSHA's excavation rules (29 CFR 1926 Subpart P) set the numbers:

  • A protective system (sloping, benching, shoring or a trench shield) is required in every excavation, unless it is in stable rock or under 5 feet deep with a competent person finding no sign of a cave-in.
  • Excavations deeper than 20 feet need a protective system designed by a registered professional engineer.
  • Trenches 4 feet or deeper need a ladder, ramp or other way out within 25 feet of lateral travel for every worker.
  • Spoil piles and equipment stay at least 2 feet back from the edge.
  • A competent person inspects the excavation daily before work and after rain or any change that raises the hazard.

Caught-between also covers workers pinned between equipment and a fixed object, and unguarded moving parts on tools and machines.

Electrocution

Electrical hazards include overhead and buried power lines, temporary power, damaged cords and energized work. Two rules carry much of the weight:

  • On construction sites, 120-volt, single-phase, 15- and 20-amp receptacle outlets that are not part of the permanent wiring need ground-fault circuit interrupters (GFCIs), or the employer must run an assured equipment grounding conductor program (29 CFR 1926.404(b)(1)).
  • Cranes and similar equipment working near power lines up to 50 kV must keep at least 10 feet away (29 CFR 1926.1408), with larger distances for higher voltages.

A worked example: ladders in a 100-foot trench

Illustrative job. A utility crew is digging a trench 6 feet deep and 100 feet long.

  1. Depth is 5 feet or more, so a protective system is required. A trench shield is chosen.
  2. Depth is 4 feet or more, so every worker needs a way out within 25 feet of lateral travel.
  3. One ladder covers 25 feet in each direction, or 50 feet of trench.
  4. Ladders needed: 100 ÷ 50 = 2, placed about 25 feet and 75 feet from one end, inside the shielded area.
  5. The excavated soil goes at least 2 feet back from the edge, and the competent person inspects before the shift and after any rain.

Count wrong and put one ladder at the end, and a worker at the far end is 100 feet from the exit: four times the limit.

How do the Focus Four connect to cost?

Each of the four is a severity hazard: low frequency, very high cost per event. They sit in the top-right corner of a frequency-severity matrix, where the best controls are the ones that remove or isolate the hazard rather than rely on behavior. A good starting point for an owner is to list the company's work that involves each of the four, name the control in place for each, and name who checks it. Every event or near miss involving one of the four deserves an incident investigation.

Quick answers

What are OSHA's Focus Four hazards in construction?

Falls, struck-by, caught-in or -between, and electrocution. OSHA uses them as the core of its 10-hour and 30-hour construction outreach training.

Is the Focus Four the same as the Fatal Four?

Yes, they are the same four hazard groups. Fatal Four is the older name; OSHA's training materials now call them the Focus Four.

How deep can a trench be before it needs a protective system?

Under 29 CFR 1926.652, a protective system is required unless the excavation is in stable rock or is less than 5 feet deep and a competent person finds no indication of a possible cave-in.

Terms in this entry
Construction Focus Four
OSHA's four core construction hazards: falls, struck-by, caught-in or -between, and electrocution. Formerly called the Fatal Four.
Competent person
Under OSHA's construction rules, someone able to identify existing and predictable hazards who has authority to take prompt corrective action. Fall training and trench inspections must be done by one.
Frequency–severity matrix
A two-by-two grid of how often a loss happens against how large it is. Each box suggests a first treatment: retain, retain and prevent, transfer and reduce, or avoid.
Sources and standards
  1. Construction Focus Four Training · OSHA
  2. 29 CFR 1926 Subpart P: Excavations · eCFR (National Archives)
  3. 29 CFR 1926 Subpart K: Electrical · eCFR (National Archives)
  4. 29 CFR 1926.1408: Power line safety (up to 350 kV) · eCFR (National Archives)
  5. 29 CFR 1926.601: Motor vehicles · eCFR (National Archives)
  6. Census of Fatal Occupational Injuries, 2024 · U.S. Bureau of Labor Statistics

Worked examples use illustrative numbers unless a source is named. This entry explains general concepts; it isn't legal, tax or coverage advice for a specific policy or contract.

Brandon Junkin
Brandon Junkin, Founder of Frost

I built Frost, the risk management platform approved insurance agents use to run contractor risk programs. Seven years in IT taught me to fix the cause, not the symptom. More about Frost

Related in the Library

Want this run for your company?

Approved Frost agents deliver full-service fractional risk management on Frost: your total cost of risk, a plan with owners and documented savings, at a fraction of the cost of a risk department.

Find an approved agent